Siloxane Water Repellent

Home :: Repellents :: Siloxane Water Repellent
Siloxane Water Repellent
View detailed images (1)
Siloxane Water Repellent

Product Downloads

Download Technical Data
Download MSDS

WR-10 SILOXANE WATER REPELLENT 23-10X

TUF-TOP "WR-10" is a solvent based siloxane water repellent designed to render water repellency to old and new masonry. It provides a long lasting, breathable barrier which exhibits excellent resistance to water, airborne dust and dirt, acid rain, salt, efflorescence, and freeze/thaw damage and spalling. The water repellency of WR-10 does not allow the substrate to retain moisture and therefore prevents growth of mold and mildew. Also available in %, 15, & 17 % Solids Concentrations.

Siloxane Water Repellent is Best Used for

  • Most masonry surfaces

    Most masonry surfaces

  • Concrete

    Concrete

  • Concrete pavers

    Concrete pavers

  • stucco

    Stucco

  • Brick

    brick

  • Split faced and fluted block

    Split faced and fluted block

  • Mortar

    Mortar

  • Roof tiles

    Roof tiles

  • Bridge Decks

    Bridge Decks
SKU SXWR
Carrier Solvent
Compliance
Primer None required
Usage on Unpainted Surfaces Concrete Floors
Concrete Walls
Concrete Drives
Block Walls
Pool Decks
Use to Recoat
 
Our price:
Quantity
Add to comparison list
Compare product with:

Technical Information

Technical Data:

SPECIFIC GRAVITY .82
WEIGHT PER GALLON 6.85 LBS.
VOLUME SOLIDS 7.84%
WEIGHT SOLIDS 10%
FLASH POINT 80
DEGREES F.  
CLEAN UP: Mineral spirits or xylene
APPLICABLE STANDARDS: Excellent
COVERAGE (THEORETICAL): SMOOTH OR PRECAST
CONCRETE 125-175*
POROUS CONCRETE 100-150*
SPLIT FACED BLOCK 50-75*
FLUTED BLOCK 25-50*
CONCRETE BLOCK 75-125*
BRICK 100-150*
ROOF TILES 75-125*

* A MOCK UP AREA SHOULD BE TESTED WITH A RILEM TAKE UP TUBE TO DETERMINE EXACT COVERAGE NEEDED TO ACHIEVE WATER REPELLENCY. CONTACT TUF-TOP FOR DETAILS/INSTRUCTIONS

Applicable Standards:

MEETS OR EXCEEDS THE FOLLOWING AT PROPER COVERAGE RATE:

  • SS-W-110C
  • ASTM E514
  • TT-C-555b
  • ASTM C67
  • ASTM 96-66
  • ASTM E96
  • ASTM G23F
  • ASTM C642
  • NCHRP-244

Usage Information

Preparation:

Surface to be coated should be clean, porous, and dry. Remove all dirt, grease, oil, wax, mildew and excessive chalk and surface and all efflorescence from the surface. High pressure washing is recommended to remove dirt and open up the pores of the concrete. Reasonable effort should be made to repair all loose or missing mortar, flashing, vapor barriers, expansion joints etc...

Application:

Surface to be coated should be clean and dry. Apply by flood coat, using a low pressure airless, pump up sprayer or power roller. DO NOT ATOMIZE. Best results are obtained when the product is applied in the form of droplets rather than mist. Surfaces must be " flooded/saturated ", allowing the material to run down 6 to 8 inches from the point of application. Vertical block and brick must be saturated with the material at the proper coverage rate in one coat, or two coats wet on wet. This product rely's upon penetration depth for performance. The deeper the penetration, the better the performance. If the material is not applied at the proper coverage and is allowed to dry, it must be re-applied at the proper square footage, and not " touched-up" with the missing amount. Always work from the bottom up to insure complete coverage. Two coats are generally recommended, depending upon surface porosity.

Limitations:

  • Not for use on the following : marble, limestone, or other forms of calcium carbonate. May inhibit over-coating.
  • Will not "bridge" cracks or spaces wider than 0.2 mm. Do not apply at temperatures below 45 degrees Fahrenheit.
  • WR-10 will not inhibit water penetration through cracked, or unsound surfaces, or surfaces with defective flashing, caulking, or structural water proofing design.

Drying Time:

  • TO TOUCH - 3 HOURS
  • RECOAT - OVERNIGHT
  • FULL CURE - 7-10 DAYS