150-250 sq. ft./gal depending on porosity and texture of substrate
DILUENT
Water
CLEAN-UP
Soap and Water
VOC CONTENT
<50 GR/LITER
ODOR
Very Slight
APPEARANCE
Color dependent
GLOSS
Satin-Semi
LIGHT STABILITY
Excellent
DURABILITY
Excellent
WATER RESISTANCE
Excellent
GASOLINERESISTANCE
Good
TENSILESTRENGTH
Excellent
BONDING
Good
SCUFF RESISTANCE
Excellent
EPA AIM CATAGORY
Floor coating
LIMITATION OF LIABILITY: The Manufacturer and/or the Seller warrants that if any goods supplied prove defective in workmanship ormaterial, that Manufacturer and/or Seller shall replace them or refund the purchase price. This warranty is made in lieu of any and all otherwarranties expressed or implied. Before application, the User shall determine the suitability of the product for his intended use and User assumes allrisks and liabilities whatsoever in connection therewith. Under no circumstances shall the Manufacturer and/or Seller be liable for incidental, consequentialor other damages for alleged negligence, breach or warranty, or strict liability arising out of use or handling of this product. The sole liabilityof Manufacturer and/or Seller for any claims arising out of the use of sale of the product shall be for the User’s purchase price.
Usage Information
Preparation:
*CONCRETE & MASONRY —Make sure concrete is sound and not crumbling. Dirt,oil, grease, mold and mildew, and any othercontaminates must be removed from the surface and pores of the concrete to insure that the paint has good contact with theconcrete. Remove oil, grease, and any othercontaminants with strong detergent, TSP, or degreasers and rinse thoroughly. Makecertain algae or mildewis treated with bleach and rinsed thoroughly. It is often advisable to pressure wash the surface to insurecomplete removal of the contaminates. Slick or smoothly trowelled bare concrete must be etched with a 10% muriatic acidsolution until the concrete pores are opened up and a sandpaper-like (120-220) grit feel is given to the concrete.Acid must bethoroughly washed off after application. May not adhere to some alkyd, epoxy, urethane, silicates or silicone modified coatings,a test patch is recommended.
*PREVIOUSCOATINGS -All previous coatings must be compatible ( if unsure, apply test patch and check adhesion with ducttape after 3 days ) and in sound, well adhered condition. Check adhesion with duct tape.All loose and degraded coatings must beremoved to a sound surface.Thoroughly degrease and pressure wash to remove all contaminates and loose or poorly adheredcoating.Allow to dry a minimum of 24 hours before coating.
Application:
Apply with roller, brush, airless, or conventional type sprayer. Roller nap size from 3/8” to 1/2" , Microfiber orQuality shed resistant cover.For most applications, “thin”coats are preferred. Apply first coat, allow to dry (2-4 hours dependingon weather), and apply second coat. For best results do not dilute. Allow a minimum of 6 hours@70 deg F. for Lt. foot traffic.
Limitations:
Do not apply when air or surface temperatures are below 55°F or are expected to fall there before coating can dry.
Do not apply to a wet or damp surface or within 6 degrees of the dew point
May not adhere to some alkyd, epoxy, urethane, silicate or silicone modified coatings, a test patch and adhesion test is alwaysrecommended.
Do not apply when it may rain or if dew may condense on the surface before D- 289 will have a chance to dry.
Do not allow to freeze. Store above 32°F(0°C).
Apply in thin coats only, overapplication may result in extended dry times or poor durability.THIS IS A GLOSSY PAINT AND IT WILL GET SLIPPERY WHEN WET. IF THE SURFACE HAS NOT ALREADY BEEN TREATED TO REDUCE SLIP HAZARDS, SAND OR OTHER MATERIAL SHOULD BE ADDED TO THIS PRODUCT BEFORE OR DURING APPLICATION TO REDUCE THIS CONDITION. IT IS THE SOLE RESPONSIBILITY OF THE APPLICATOROR OWNER TO DETERMINE THE SUITABILITY AND SAFETY OF APPLYING THIS PRODUCT IN AREAS OF PEDESTRIAN TRAFFIC.
Drying Time:
Normally dries in 1-3 hours and can be walked on ( Lt. foot traffic ) after 6 hours. 36-48 hours are suggestedbefore heavy foot traffic. Low temperatures and high humidity can extend drying and curing time.
