Aqua-Tite Water and Oil Repellent

Home :: Repellents :: Aqua-Tite Water and Oil Repellent
Aqua-Tite Water and Oil Repellent
View detailed images (1)
Aqua-Tite Water and Oil Repellent

Product Downloads

Download Technical Data
Download MSDS

WATER/OIL REPELLENTFOR CONCRETE, MASONRY, GRANITE, STONE & MARBLE

A test patch is recommended to check for compatibility.

AQUA TITE-FP is a water based proprietary solution that provides a durable, transparent protective barrier against oil and water on concrete and other porous masonry or mineral surfaces. AQUA-TITE FP chemically bonds with the surface, providing long-term, invisible barrier protection. Excellent water/oil repellent coating for driveways, vehicle bays, light industrial flooring, aircraft hangers, concrete, brick, grout, terra cotta, sandstone, unglazed decorative tiling, gypsum drywall, unpolished stone and granite surfaces, stucco, roof tiles and plaster.

Aqua-Tite is Best Used for

  • Concrete and Masonry

    Concrete and Masonry

  • Pavers and Deco Block

    Pavers and Deco Block

  • Natural Stone

    Natural Stone

  • Stucco

    Stucco

  • Un-Polished Marble and Granite

    Un-Polished Marble and Granite

  • Unglazed Tile

    Unglazed Tile

Technical Information

Limitations:

  • Do not apply to coated, glazed, polished or smooth surfaces as it may etch or damage the surface.
  • Do not apply to glass, wood or aluminum, etching may occur.
  • DO not apply to glazed anything.
  • Will not "bridge" cracks wider than 1mm.
  • Not for use on shale or other oil rock..
  • Light colored surfaces may show the surface staining from contaminants, but will be removable by cleaning.
  • Do not apply to painted or sealed surfaces.
  • Do not apply when it may rain before Aqua-Tite FP will have a chance to dry.
  • Do not allow to freeze. Store above 32 degrees Fahrenheit.
  • Do not apply when air or surface temperatures are below 40 degrees Fahrenheit or are expected to fall there before coating can dry.

Drying Time:

Normally dries in 2-4 hours and cures in 24-48 hours. Low temperatures and high humidity can extend drying/curing time.
SKU ATWOR
Carrier
Compliance
Primer
Usage on Unpainted Surfaces
Use to Recoat
 
Our price:
Quantity
Add to comparison list
Compare product with:

Technical Information

Technical Data:

SOLIDS
100 % active, 6% weight
COVERAGE
150-400 sg.ft/gallon depending on porosity/texture of substrate
DILUENT
WATER-DO NOT DILUTE
CLEAN-UP
Soap and water
ODOR
None
APPEARANCE
Water clear/dries invisible
LIGHT STABILITY
Excellent
DURABILITY
Excellent
WATER RESISTANCE
Excellent
EPA AIM CATEGORY
Water repellent sealer

Stain Resistance:

2 hour stop test, cleaned
SOLIDS
100 % active, 6% weight
COVERAGE
150-400 sg.ft/gallon depending on porosity/texture of substrate
DILUENT
WATER-DO NOT DILUTE
CLEAN-UP
Soap and water
ODOR
None
APPEARANCE
Water clear/dries invisible
LIGHT STABILITY
Excellent
DURABILITY
Excellent
WATER RESISTANCE
Excellent
EPA AIM CATEGORY
Water repellent sealer

Stain Resistance:

2 hour stop test, cleaned
LEADING BRAND
AQUA-TITE FP
WATER
0
0
OIL
5 ABSORBED
0
BACON GREASE
5 ABSORBED
0
COFFEE
1
0
SOY SAUCE
4
2
MUSTARD
2
0
BBQ SAUCE
5
1

 
0- BEST- NO STAINING
1- SLIGHT STAINING
2-LIGHT STAINING
3- MODERATE STAINING
4-HEA VY STAINING
5-ABSORBED/STAINED
* * This product will inhibit most common staining elements, but should not be considered" stain proof". If certainstaining elements are to be encountered commonly, a test should be made to determine the suitabilIty of this productfor the intended use. It is the sole responsibility of the owners or applicators to determine the suitability of this productfor it's intended use, and assumes all risks and liabilities in connection therewith.

Usage Information

Limitations:

  • Do not apply to coated, glazed, polished or smooth surfaces as it may etch or damage the surface.
  • Do not apply to glass, wood or aluminum, etching may occur.
  • DO not apply to glazed anything.
  • Will not "bridge" cracks wider than 1mm.
  • Not for use on shale or other oil rock..
  • Light colored surfaces may show the surface staining from contaminants, but will be removable by cleaning.
  • Do not apply to painted or sealed surfaces.
  • Do not apply when it may rain before Aqua-Tite FP will have a chance to dry.
  • Do not allow to freeze. Store above 32 degrees Fahrenheit.
  • Do not apply when air or surface temperatures are below 40 degrees Fahrenheit or are expected to fall there before coating can dry.

Drying Time:

Normally dries in 2-4 hours and cures in 24-48 hours. Low temperatures and high humidity can extend drying/curing time.